haapride.blogg.se - Sbloccare alice gate 2 plus voip wifi phone

SBLOCCARE ALICE GATE 2 PLUS VOIP WIFI PHONE INSTALL
SBLOCCARE ALICE GATE 2 PLUS VOIP WIFI PHONE SERIAL
SBLOCCARE ALICE GATE 2 PLUS VOIP WIFI PHONE DRIVER
SBLOCCARE ALICE GATE 2 PLUS VOIP WIFI PHONE SOFTWARE

The following steps is needed only if your OpenWrt router does not supports multiple SSID and you have a RT72 driver compatible device, otherwise you must use your device proper driver. The SSH access allows us to run configuration command throgh a SSH terminal.īefore going on we have to say that the WiFi board of this router does not support multiple SSID, so we have to use a USB adapater. Just open the Luci web interface of your OpenWrt, set your password and enable a SSH access to the main lan. Now that you have a working OpenWrt device, we can setup it to provide the main WiFi access and a guest WiFi access.

SBLOCCARE ALICE GATE 2 PLUS VOIP WIFI PHONE SERIAL

Note: if you would like to change your IP address using serial interface, just edit the network config file using the command vi etcconfignetwork You should change the ipaddr of the interface lan, also you can add your gateway and dns option here. The router will reboot, and you can now access the router by the 192.168.1.1 address on your web browser. Supposing your interface is 192.168.1.120, on the CFE prompt you have to run the flashimage command as follow flashimage 192.168.1.120:openwrt-15.05.1-brcm63xx-generic-AGV2W-squashfs-cfe.bin This would load the firmware on your router.

SBLOCCARE ALICE GATE 2 PLUS VOIP WIFI PHONE SOFTWARE

Just put the firmware in your tftpd32 folder, run the software and select the server interface to serve. Im using tftpd32 ( ) and the Chaos Calmer 15.05.1 firmware ( ). You have to run a TFTP server, to provide the firmware to your router. To enter the CFE prompt, you can press any key during the boot process, when the countdown stop message appears.

Here you can the serial connection pins, on the left the GND, top right RX, bottom right TX). Sbloccare Alice Gate 2 Voip Wifi Devices Serial Connection Pins Summarizing it will be very simple, you just have to connect the router to a RS232 port, set the port at 115200 baud, no parity, 8bits and open your terminal software. The following steps may brick your device, so continue at your risk. The first step to start the game will be load the OpenWrt firmware. The following steps is needed only if your router hasnt OpenWrt on board. Lets suppose we are serving our main network on 192.168.1.024 ip ranges, and we would like a guest network, isolated from the 192.168.1.024 one, on the 192.168.2.024 ip range. This post reports how Ive built a Access Point and a Routed Access Point for a Guest WiFi using OpenWrt. Ive saved three of them from junkyard and I start playing with that devices. OpenWrt is a linux distribution for embedded devices, you can find further information on the openwrt website.Īlthough hardware Voip and ADSL is not supported on this router, this device can be pretty usefull for other network roles. The Pirelli Alice Gate VoIP 2 Plus, also known as agpf, is a ADSL modem router with WiFi and Voip capabilities. OpenWrt Access Point Routed AP with Guest WiFi on AGPF modemrouter.

SBLOCCARE ALICE GATE 2 PLUS VOIP WIFI PHONE INSTALL

We will install the Ralink RT2501USBRT2571W (RT73) module opkg install kmod-rt73-usb We will now reboot.

Sbloccare Alice Gate 2 Voip Wifi Devices Serial Connection PinsĬome faccio a navigare Grazie in anticipo a chiunque mi risponda.Ĭomunque, nella pagina LANEthernet Properties, alla riga IP Address Distribution (in blu, tutte le altre sono nere) mi dice disabled.ĭevi modificare questa connessione in base alla configurazione del tuo operatore (Teletu).Ĭon questo fw non avresti nessun problema anche in caso di cambio operatore.